List of shared models

[gianfranco]

Fender Twin Reverb and Champ by @Boukman

@Boukman

I made a capture of my Fender Twin Reverb Vib channel (Silverface to Blackface conversion)
and my Champ 5F1 clone.
Hope you like them!
Champ G9.json (171.6 KB)
Fender Twin CH2.json (170.8 KB)

[gianfranco]

Boss Katana Mini - 3 Channels by @novemberist

@novemberist

this one is obviously more for fun and probably not very useful for most of you. But I think the model sounds quite good - like the real Mini. Captured with Mid-Gain on the 3 available channels (Clean,Crunch,Brown) respectively. EQ-knobs all at 12 o’clock.

Boss_Katana_Mini_Clean.json (15.7 KB)
Boss_Katana_Mini_Crunch.json (15.7 KB)
Boss_Katana_Mini_Brown.json (15.7 KB)

[gianfranco]

BASS: Darkglass AO900 by @Charan_Mellor

@Charan_Mellor

Here are three light models of the preamp section of my Darkglass AO900
All knobs set to ~noon, EQ flat

Enjoy!

DGAO900-clean_LSTM-12-0.json (32.5 KB)
DGAO900-dirty-light drive_LSTM-12-0.json (32.0 KB)
DGAO900-dirty-med drive_LSTM-12-0.json (32.3 KB)

[gianfranco]

Marshal JMP Low Sensitivity Input - Pedal platform, clean. by @mreed707

Two Notes Captor
Sounds great with Guitarix Gxcabinet 4x12 with treble set at 10 o’clock.
Heavy - ESR 0.003 (on third attempt, the first 2 were 0.011 - didn’t change anything just kept running the cell)
A/B against real amp very very close, amazed.
Sounds great with DIY OCD, Rat and TS-9
JMP Low Input.json (81.5 KB)

Did this sound good to you

[gianfranco]

Diplomacy by @LievenDV

@LievenDV

Diplomacy
Version 3 (3rd attempt, best result so far)
High gain amp, modelled after the free amp VST:
Ignite Emissary (STL Tones), a loud metal machine!

@LievenDV

Diplomacy-amp-high-gain.json (53.5 KB)

[gianfranco]

“Schmitt | based on Bogner Uberschall rev blue” by @LievenDV

@LievenDV

I modelled a SVT representation of the Bogner Uberschall rev. blue.
Little noise and a powerful low oomph.

@LievenDV

Schmitt_High-Gain-Amp-by-LievenDV.json (53.2 KB)

[gianfranco]

Hailstorm | high gain based on EVH 5150 III 100W by @LievenDV

@LievenDV

Based on an SVT version of the EVH 5150 III 100W
High gain channel

@LievenDV

Hailstorm-high-gain-by-LievenDV.json (53.3 KB)

[gianfranco]

Ibanez TSA5TVR by @malfunction54

@malfunction54

I profiled my little Ibanez 5W tube amp. When paired with a Jensen C8R IR, it sounds reasonably close to the real thing. This profile is clean, but I recorded on max volume. It is fairly easy to push into breakup. Treble at 10 o’clock, bass at 2 o’clock, built-in spring reverb off, and built-in TubeScreamer circuit off.
Ibanez TSA5TVR.json (171.3 KB)

[gianfranco]

JMP low sensitivity Pedal Platform by @mreed707

@mreed707

https://forum.mod.audio/uploads/short-url/eNi7sXKpyz9KVjhCEWQqWBnDKjF.json

JMP low sensitivity input pedal platform

[gianfranco]

Jad Freer Capo - Bass preamp by @mrdinsdale

@mrdinsdale

Above settings with both A & B sides engaged with B into A:
capo-b-into-a.json (31.7 KB)

Same again but just the A side:
capo-a.json (31.8 KB)

[gianfranco]

EAE Halberd v2 and Longsword V4 by @mrdinsdale

@mrdinsdale

Heres a few rough captures based on the Electronic Audio Experiments Halberd and Longsword pedals.

This is a first pass and need to take more time to A/B them with the real thing, once I’m happy with the results I’ll expand the captures to include a few different flavours as both are hugely responsive to the settings.

Halberd V2

Thick and crunchy - Heaviest voicing with Gain, Tone and Depth set to 1 o’clock.
eae-halberd-thick-crunch.json (31.7 KB)

Thick and chewy - Heaviest voicing with Gain and Depth at around 3, Tone at 1 o’clock
eae-halberd-thick-chewy.json (31.7 KB)

Longsword

Bass settings with boost - Silicone clipping with bass boost. Gain at 12, boost at around 11
eae-longsword-bass-settings-with-boost.json (31.7 KB)

[gianfranco]

Marshall JCM900 by @Rafa_Ruiz

@Rafa_Ruiz

HI everyone!! Second chance… this time a real JCM900 High Gain Dual Reverb Combo.(only preamp) I used the DI out direct to my MOD Dwarf and record everything without any other kind of hardware… easy and AMAZING!! I´m just starting with this tec,but there are endless possibilities I think… Hope anyone can find it useful, I use it with a tubescreamer in front of it (software in my MOD Dwarf) and it crank very well…a 4x12 simulation a bit of EQ and ready…

JCM 900_LSTM-16-0.json (53.4 KB)

[gianfranco]

Traynor Dark Horse by @Trilby

@Trilby

The models I’m sharing today are in the “Pure” mode at the full 15W, master volume at noon (again, tone stack is lifted, so treble/bass have no effect). One capture is with the Gain knob at about 2 o’ clock, the other at full.

Models:
Dark Horse - Pure-Gain 2oc - Master 12oc.json (31.8 KB)
Dark Horse - Pure-Gain Full - Master 12oc.json (31.9 KB)

[gianfranco]

Victory VX Kraken Models by @lordsilly

@lordsilly

I’ve made two models so far of channel 2, one with and one without the bass focus switch engaged. I used the settings I generally like to use personally (shown in the picture).

Victory-VX-CH2-FOff-G5-Heavy.json (80.8 KB)
[Victory-VX-CH2-FOn-G5-Heavy.json|attachment](/uploads/short-url/jR3ikEnZT6Tv

@lordsilly

• I’ve made a new model of just the preamp section on the same settings as above, captured straight from the effects send of the Kraken.

Victory-VX-CH2-Pre-G5-Heavy.json (80.5 KB)

EKmPkUQ4KI3gmZu.json) (80.6 KB)

@lordsilly

Update - Whole bunch of CH1 models at two quite low gain levels. As before through power amp - with focus on and off - and through preamp only versions.

Victory-VX-CH1-FOff-G1-Heavy.json (81.2 KB)
Victory-VX-CH1-FOff-G4-Heavy.json (81.0 KB)
Victory-VX-CH1-FOn-G1-Heavy.json (81.4 KB)
Victory-VX-CH1-FOn-G4-Heavy.json (81.2 KB)
Victory-VX-CH1-Pre-G1-Heavy.json (81.3 KB)
Victory-VX-CH1-Pre-G4-Heavy.json (81.0 KB)

@lordsilly

Victory-VX-CH1-FOff-G1-Heavy.json (81.2 KB)
Victory-VX-CH1-FOff-G4-Heavy.json (81.0 KB)
Victory-VX-CH1-FOn-G1-Heavy.json (81.4 KB)
Victory-VX-CH1-FOn-G4-Heavy.json (81.2 KB)
Victory-VX-CH1-Pre-G1-Heavy.json (81.3 KB)
Victory-VX-CH1-Pre-G4-Heavy.json (81.0 KB)

[gianfranco]

Soldano SLO by @Rafa_Ruiz

@Rafa_Ruiz

TIis time a capture of a Soldano SLO amp emulator with some eq … I was using it with my dwarf in some gigs and it was nice , so maybe can be useful for you too…

SLO Overdrive_LSTM-16-0 (1) (1).json (53.3 KB)

[gianfranco]

Bogner Ecstasy amp head

@gianfranco

Multiple Channels of the Bogner Ecstasy Amp Head

@gianfranco

Bogner 1_LSTM-16.json (53.3 KB)
Bogner Blue_LSTM-16.json (53.4 KB)
Bogner Green_LSTM-16.json (53.6 KB)
Bogner Plexi Red_LSTM-16.json (53.6 KB)
Bogner Plexi_LSTM-16.json (54.0 KB)

[gianfranco]

VX Kraken Ch1 through Randall V30 + SH57 by @jazzbre

@jazzbre

Hi,
I tried replicating my base amp + cabinet and I think it turned out well.
This was recorded with the exact settings I use normally when mic-ed (I didn’t exactly nail mic placement this time). I didn’t use the real input.wave but I just played weird stuff on different pickups and settings for about 5mins.
For a first and really hacky test I think it turned out pretty good, that’s why I’m sharing it here.

-A
Victory_VX_Channel1_RandallV30.json (81.2 KB)

[gianfranco]

Brunetti 059 by @UnvisualStudio

@UnvisualStudio

Hi! I’ve done some captures from my amp and I want to share them with you:

Brunetti 059

[gianfranco]

Diezel based amp (simil Herbert) by @Teuvosick

@Teuvosick

3 captures of this amp, not the original, is like a homemade, I lost the logs and esr but under 0.03

Cheers

herbert ch2 clean.json (53.6 KB)
herbert ch2 drive.json (53.4 KB)
herbert ch2+ lead.json (53.4 KB)

[gianfranco]

Mercuriall Reaxis and Vtar Slowrunner by @Boukman

@Boukman

I ripped 2 of my favourite sounds from modelers.
SLowrunner.json (53.2 KB)
Ampbox Reaxis Hells kitchen lead.json (53.3 KB)