List of shared models

[gianfranco]

Peavey VK100 HEAD HIGAIN Lead Channel by @ReedDunn

@ReedDunn

HI REED DUNN here with my First upload for MOD site!

ReedD VK100 personal setting.json (199.4 KB)

This is my second capture of my Vk100 this one is from my Neural Amp Modeler training NAM captures re trained for AIDA-X. More to Come.pretty heavy tone that i use on my amp.just past half for eq on sweet spots.and 3/4 for dampening and presence. lead channel with gain boost and volume boost.tube type dial is fully left for that extra power to the lead channel pre amp tubes. I hope you enjoy. only wish i have is for a noise gate in AIDA-X but i can easily use a fee one like GVST - GGate before AIDA-X works great.!!!KEEP IT LOUD!!!

[gianfranco]

Ceriatone King Kong - Part 3 (hotter) by @Boukman

@Boukman

Hi again!
I tried a few captures with hotter input signal.Let me know what you think
Ceriatone King Kong Channel 1 60s.json (170.3 KB)
KK new 60s br sw2 L .json (171.0 KB)
KK new 70s br sw2 L .json (170.9 KB)
KK new 80s br sw2 L .json (170.5 KB)

[gianfranco]

Ceriatone King Kong - Part 3 (boosted) by @Boukman

@Boukman

Hi!
I made a few more captures of my amp.I think they are getting better!I used some pedals in some captures to boost it.I`m really pleased with the sound!!
I think it sounds better than Line6 Helix already with the AIDA!!
Cheers!!

KK Ch2 Br sw both L feel dn 60s deep c bright R Lead 80s .json (170.5 KB)
KK Ch2 Br sw off feel dn 60s deep c bright r Guvnor boost - target.json (170.6 KB)
KK Ch2 Br sw both L feel dn 60s deep c bright R - target.json (170.5 KB)
KK CH2 Brsw both L feel dn 70s deep C bright R.json (170.9 KB)
KK Ch2 G1 Br sw L 70s deep c bright R Feel Up Hudson Broadcast.json (170.7 KB)

@Boukman

KK Ch1 Br sw L 60s deep c bright R boost SD.json (170.8 KB)
KK Ch2 G1 Br sw L 80s deep c bright R Feel Up.json (170.7 KB)
KK Ch2 G1 Br sw L 60s deep c bright R Feel Up DemonTS9 K.json (170.7 KB)
KK Ch1 Br sw L 60s deep c bright R Protein - .json (170.2 KB)
KK Ch1 Br sw L 60s deep c bright R Barber DD.json (170.7 KB)

[gianfranco]

Full “channel strip” for Electric Nylon Guitar by @Loris_Donatelli

@Loris_Donatelli

This is taken from the Logic settings, it’s my “channel strip” and is useful for a classical guitar sound, when the nylon string instrument has no microphone but only a piezo system. The reverb is already present, if someone wants it without I will do it again without so that you can choose the right reverb. Currently there is only EQ and COMP.
Electric Nylon Guitar.json (172.2 KB)

[gianfranco]

Victory Countess (The Jack) V4 Preamp by @Boukman

@Boukman

Here are some profiles of my tube preamp clean and drive channels at various gain settings.
Try using the power amp impulses plugin after.It works really nice!!
Victory Countess V4 Ch1 G 4 .json (171.2 KB)
Victory Countess V4 Ch2 G full.json (170.2 KB)
Victory Countess V4 Ch2 G 3q .json (170.5 KB)
Victory Countess V4 Ch2 Gain Half.json (170.6 KB)
Victory Countess V4 Ch2 Gain 1Q.json (170.8 KB)

@Boukman

Victory Countess V4 Ch1 G 9.json (170.8 KB)
Victory Countess V4 Ch1 G 6.json (170.9 KB)

@Boukman

I made this with lower gain…I think they sound clearer…
Victory V4 CH2 Gain 7.5 di 5 -11 lower esr.json (170.4 KB)
Victory V4 CH2 Gain 3 di 5 -11 - .json (170.5 KB)

[gianfranco]

Catalinbread DLS (Marshall Plexi Super Bass) by @novemberist

@novemberist

This is a model of my Catalinbread Dirty Little Secret pedal, which basically emulates the sound and character of a classic Marshall Plexi amp (set to “Super Bass” circuit in my case). I’ve chosen the lightest model for this one and have sampled 4 different degrees of the preamp knob (low,center,high,very high). No cab simulation of any kind included.

CB_DLS_Preamp_Low.json (15.7 KB)
CB_DLS_Preamp_Center.json (15.7 KB)
CB_DLS_Preamp_High.json (15.7 KB)
CB_DLS_Preamp_VeryHigh.json (15.7 KB)

[gianfranco]

AX84 P1 DIY Amp - Amp Only by @mreed707

@mreed707

Single 12AX7 and a single EL34 amp. Marshall sounding JTM ish. Set up as a pedal platform so just a little bit of break up. DI through Two Notes Captor into Logic. Guitar used, Fender Mustang with humbuckers so pushing the front a bit more than a single coil.
Clean AX84 P1.json (81.4 KB)

[gianfranco]

Fender Twin Reverb by @Boukman

@Boukman

I made a capture using the TS808 a la SRV.
Fender Twin Reverb TS808 g-11 di half .json (171.1 KB)

[gianfranco]

Fender Twin Reverb and Champ by @Boukman

@Boukman

I made a capture of my Fender Twin Reverb Vib channel (Silverface to Blackface conversion)
and my Champ 5F1 clone.
Hope you like them!
Champ G9.json (171.6 KB)
Fender Twin CH2.json (170.8 KB)

[gianfranco]

Boss Katana Mini - 3 Channels by @novemberist

@novemberist

this one is obviously more for fun and probably not very useful for most of you. But I think the model sounds quite good - like the real Mini. Captured with Mid-Gain on the 3 available channels (Clean,Crunch,Brown) respectively. EQ-knobs all at 12 o’clock.

Boss_Katana_Mini_Clean.json (15.7 KB)
Boss_Katana_Mini_Crunch.json (15.7 KB)
Boss_Katana_Mini_Brown.json (15.7 KB)

[gianfranco]

BASS: Darkglass AO900 by @Charan_Mellor

@Charan_Mellor

Here are three light models of the preamp section of my Darkglass AO900
All knobs set to ~noon, EQ flat

Enjoy!

DGAO900-clean_LSTM-12-0.json (32.5 KB)
DGAO900-dirty-light drive_LSTM-12-0.json (32.0 KB)
DGAO900-dirty-med drive_LSTM-12-0.json (32.3 KB)

[gianfranco]

Marshal JMP Low Sensitivity Input - Pedal platform, clean. by @mreed707

Two Notes Captor
Sounds great with Guitarix Gxcabinet 4x12 with treble set at 10 o’clock.
Heavy - ESR 0.003 (on third attempt, the first 2 were 0.011 - didn’t change anything just kept running the cell)
A/B against real amp very very close, amazed.
Sounds great with DIY OCD, Rat and TS-9
JMP Low Input.json (81.5 KB)

Did this sound good to you

[gianfranco]

Diplomacy by @LievenDV

@LievenDV

Diplomacy
Version 3 (3rd attempt, best result so far)
High gain amp, modelled after the free amp VST:
Ignite Emissary (STL Tones), a loud metal machine!

@LievenDV

Diplomacy-amp-high-gain.json (53.5 KB)

[gianfranco]

“Schmitt | based on Bogner Uberschall rev blue” by @LievenDV

@LievenDV

I modelled a SVT representation of the Bogner Uberschall rev. blue.
Little noise and a powerful low oomph.

@LievenDV

Schmitt_High-Gain-Amp-by-LievenDV.json (53.2 KB)

[gianfranco]

Hailstorm | high gain based on EVH 5150 III 100W by @LievenDV

@LievenDV

Based on an SVT version of the EVH 5150 III 100W
High gain channel

@LievenDV

Hailstorm-high-gain-by-LievenDV.json (53.3 KB)

[gianfranco]

Ibanez TSA5TVR by @malfunction54

@malfunction54

I profiled my little Ibanez 5W tube amp. When paired with a Jensen C8R IR, it sounds reasonably close to the real thing. This profile is clean, but I recorded on max volume. It is fairly easy to push into breakup. Treble at 10 o’clock, bass at 2 o’clock, built-in spring reverb off, and built-in TubeScreamer circuit off.
Ibanez TSA5TVR.json (171.3 KB)

[gianfranco]

JMP low sensitivity Pedal Platform by @mreed707

@mreed707

https://forum.mod.audio/uploads/short-url/eNi7sXKpyz9KVjhCEWQqWBnDKjF.json

JMP low sensitivity input pedal platform

[gianfranco]

Jad Freer Capo - Bass preamp by @mrdinsdale

@mrdinsdale

Above settings with both A & B sides engaged with B into A:
capo-b-into-a.json (31.7 KB)

Same again but just the A side:
capo-a.json (31.8 KB)

[gianfranco]

EAE Halberd v2 and Longsword V4 by @mrdinsdale

@mrdinsdale

Heres a few rough captures based on the Electronic Audio Experiments Halberd and Longsword pedals.

This is a first pass and need to take more time to A/B them with the real thing, once I’m happy with the results I’ll expand the captures to include a few different flavours as both are hugely responsive to the settings.

Halberd V2

Thick and crunchy - Heaviest voicing with Gain, Tone and Depth set to 1 o’clock.
eae-halberd-thick-crunch.json (31.7 KB)

Thick and chewy - Heaviest voicing with Gain and Depth at around 3, Tone at 1 o’clock
eae-halberd-thick-chewy.json (31.7 KB)

Longsword

Bass settings with boost - Silicone clipping with bass boost. Gain at 12, boost at around 11
eae-longsword-bass-settings-with-boost.json (31.7 KB)

[gianfranco]

Marshall JCM900 by @Rafa_Ruiz

@Rafa_Ruiz

HI everyone!! Second chance… this time a real JCM900 High Gain Dual Reverb Combo.(only preamp) I used the DI out direct to my MOD Dwarf and record everything without any other kind of hardware… easy and AMAZING!! I´m just starting with this tec,but there are endless possibilities I think… Hope anyone can find it useful, I use it with a tubescreamer in front of it (software in my MOD Dwarf) and it crank very well…a 4x12 simulation a bit of EQ and ready…

JCM 900_LSTM-16-0.json (53.4 KB)