Fender Blues Deluxe (reissue) by @TheRedOne
Then I took the pre-amp signal as an “input.wav” for the model, and the same respective mic’ed cabs as targets, to get the "cab only"
models, to use two Aida-X plugins in the chain, one with the preamp model and the other with the “cab only” model loaded to imitate four-cable fx send/return setup, so I can put some pedals before the preamp, and some - in between the preamp and the power amp of the cabinet.
4-cable setup
Surprisingly it works, and if you A/B compare a “pre+cab” model and a “pre” model to a respective “cab only” model, well, at least I was not able to hear much difference in a blind test. Try it out yourself and let me know if it works for you.
A/B test setup
Here are the “cab only” models to be used with either the preamp model above or, I guess, any other “preamp only” model.
Condenser mic on-axis close up
Fender Blues Deluxe 2a - cab only condendser mic on-axis.json (175.5 KB)
Condenser mic off-axis close up
Fender Blues Deluxe 3a - cab only condendser mic off-axis.json (175.7 KB)
Condenser mic on-axis 30cm from the cone
Fender Blues Deluxe 4a - cab only condendser mic on-axis 30cm off.json (175.8 KB)
Condenser mic off-axis 30cm from the cone
Surprisingly, after like 20 or 30 attempts to train a model with a decent ESR (in my experience - anything less than 0,04), I just couldn’t make it. All the resulting models came out with ESR around 0,07 and were quite noisy. After a few sleepless nights I just gave up. Sorry, no model here!
Dynamic mic on-axis
Fender Blues Deluxe 6a - cab only dynamic mic on-axis.json (176.7 KB)
Dynamic mic off-axis
5 Likes
Gallien Krueger 700RB II Bass Amp Head by @jtemple0967
7 Likes
A couple of pedals by @Boukman
2 Likes
Fender Twin Reberb (Vibrato Channel) and Fender Champ 5F1 Clone by @Boukman
2 Likes
Peavey VK100 HEAD HIGAIN Lead Channel by @ReedDunn
HI REED DUNN here with my First upload for MOD site!
ReedD VK100 personal setting.json (199.4 KB)
This is my second capture of my Vk100 this one is from my Neural Amp Modeler training NAM captures re trained for AIDA-X. More to Come.pretty heavy tone that i use on my amp.just past half for eq on sweet spots.and 3/4 for dampening and presence. lead channel with gain boost and volume boost.tube type dial is fully left for that extra power to the lead channel pre amp tubes. I hope you enjoy. only wish i have is for a noise gate in AIDA-X but i can easily use a fee one like GVST - GGate before AIDA-X works great.!!!KEEP IT LOUD!!!
2 Likes
Ceriatone King Kong - Part 3 (hotter) by @Boukman
2 Likes
Ceriatone King Kong - Part 3 (boosted) by @Boukman
4 Likes
Full “channel strip” for Electric Nylon Guitar by @Loris_Donatelli
This is taken from the Logic settings, it’s my “channel strip” and is useful for a classical guitar sound, when the nylon string instrument has no microphone but only a piezo system. The reverb is already present, if someone wants it without I will do it again without so that you can choose the right reverb. Currently there is only EQ and COMP.
Electric Nylon Guitar.json (172.2 KB)
5 Likes
Victory Countess (The Jack) V4 Preamp by @Boukman
4 Likes
Catalinbread DLS (Marshall Plexi Super Bass) by @novemberist
This is a model of my Catalinbread Dirty Little Secret pedal, which basically emulates the sound and character of a classic Marshall Plexi amp (set to “Super Bass” circuit in my case). I’ve chosen the lightest model for this one and have sampled 4 different degrees of the preamp knob (low,center,high,very high). No cab simulation of any kind included.
CB_DLS_Preamp_Low.json (15.7 KB)
CB_DLS_Preamp_Center.json (15.7 KB)
CB_DLS_Preamp_High.json (15.7 KB)
CB_DLS_Preamp_VeryHigh.json (15.7 KB)
3 Likes
AX84 P1 DIY Amp - Amp Only by @mreed707
3 Likes
Fender Twin Reverb by @Boukman
3 Likes
Fender Twin Reverb and Champ by @Boukman
3 Likes
Boss Katana Mini - 3 Channels by @novemberist
1 Like
BASS: Darkglass AO900 by @Charan_Mellor
3 Likes
Marshal JMP Low Sensitivity Input - Pedal platform, clean. by @mreed707
Two Notes Captor
Sounds great with Guitarix Gxcabinet 4x12 with treble set at 10 o’clock.
Heavy - ESR 0.003 (on third attempt, the first 2 were 0.011 - didn’t change anything just kept running the cell)
A/B against real amp very very close, amazed.
Sounds great with DIY OCD, Rat and TS-9
JMP Low Input.json (81.5 KB)
Did this sound good to you
3 Likes
“Schmitt | based on Bogner Uberschall rev blue” by @LievenDV
2 Likes
Hailstorm | high gain based on EVH 5150 III 100W by @LievenDV
1 Like