List of shared models

[gianfranco]

Friedman HBE and Dual Rectifier by @Teuvosick

@Teuvosick

Friedman HBE
hbe L 2 esr 0.035.json (53.4 KB)
recommended an Orange PPC 4x12 V30 IR

Dual Rectifier
recto R 3 esr 0.073.json (53.3 KB)
recommended a Mesa straight 4x12 V30 IR

[itskais]

Harley Benton TUBE15 Celestion
AMP only, no cabinet included.

@itskais

capture1: gain 3, vol 10
AMP HB Clean1.json (53.7 KB)
capture2: gain 5, vol 9
AMP HB Clean2.json (53.7 KB)
capture3: gain 7, vol 8
AMP HB Clean3.json (53.8 KB)
capture4: gain 9, vol 7
AMP HB Crunchy.json (53.9 KB)

[gianfranco]

Grammatico from Line6, by @JamKid

@JamKid

Tried capturing the new model from Line 6. Supposing a dumble model.
The standard type seems to have slightly more mid response than the light version. Both sounded nice to my ears, just slight differences.
Do note that this is just the amp model without cab or IR.

Grammatico_LSTM-12.json (31.8 KB)
Grammatico_LSTM-16.json (53.8 KB)

[gianfranco]

Ceriatone King Kong - part 2 plus some other pedals @Boukman

@Boukman

Hi i made a few more
as well as 3 pedals.
It`s weird about the training because it always says “neural network found, continuing training” and stops at an epoch number 130-300.
Anyway, i hope that it gets smoother as we go…
Barber DD.json (53.6 KB)
Ibanez Mosfet.json (54.0 KB)
KK80s G6.json (53.6 KB)
KK Ch1 60s.json (53.9 KB)
KK Ch2 60s G6.json (53.6 KB)
KK CH2 70s G6.json (53.6 KB)
KK CH2 70s lead80s gswon.json (53.4 KB)
Benson Preamp.json (53.8 KB)

[gianfranco]

Hughes & Kettner Tubemeister Deluxe 20 by @malfunction54

@malfunction54

Here is my first Model. It’s my Hughes & Kettner Tubemeister Deluxe 20 on the clean channel. Will add the lead channel later, and possibly some other variants

These are made with no cabinet (only the head using the DI out), with cab simuation on the built-in RedBox turned off. I like using a good Celestion Vintage 30 IR, which is similar to my ears to the H&K TM112 cabinet
Hughes & Kettner Tubemeister Deluxe 20 - Clean.json (197.9 KB)

[gianfranco]

Ceriatone King Kong - Part 1 by @Boukman

@Boukman

I tried a few captures with hotter input signal.Let me know what you think
Ceriatone King Kong Channel 1 60s.json (170.3 KB)
KK new 60s br sw2 L .json (171.0 KB)
KK new 70s br sw2 L .json (170.9 KB)
KK new 80s br sw2 L .json (170.5 KB)

[gianfranco]

Hughes & Kettner Tubemeister Deluxe 20 , by @malfunction54

@malfunction54

Here is my first Model. It’s my Hughes & Kettner Tubemeister Deluxe 20 on the clean channel. Will add the lead channel later, and possibly some other variants

These are made with no cabinet (only the head using the DI out), with cab simuation on the built-in RedBox turned off. I like using a good Celestion Vintage 30 IR, which is similar to my ears to the H&K TM112 cabinet
Hughes & Kettner Tubemeister Deluxe 20 - Clean.json (197.9 KB)

[gianfranco]

Hiwatt DR504 Custom 50 1975 from NAM by @Zavorra

@Zavorra

To make some practice on reamping on linux I got this NAM model from ToneHunt, applied in Ardour with NAM LV2 plugin and reamped using standard settings on the AIDA-X notebook. Probably the volume is some low, but I like it and hope that some of you will find it useful

Hiwatt DR504 JU Crunch BAL DI.json (172.3 KB)

[gianfranco]

Fender Blues Deluxe (reissue) by @TheRedOne

@TheRedOne

all the models here are based on the clean channel, with treble, mid and bass knobs at 6, 8 and 6 correspondingly (the way I set 'em at gigs).
I used an Oktava mk-519 condenser mic and Sennheiser e906 dynamic mic.

The models:

Preamp (no cab)

Fender Blues Deluxe 1 - preamp.json (176.0 KB)

Condenser mic on-axis close up

Fender Blues Deluxe 2 - pre+cab condendser mic on-axis.json (175.5 KB)

Condenser mic off-axis close up

Fender Blues Deluxe 3 - pre+cab condendser mic off-axis.json (176.0 KB)

Condenser mic on-axis 30cm from the cone

Fender Blues Deluxe 4 - pre+cab condendser mic on-axis 30cm off.json (175.3 KB)

Condenser mic off-axis 30cm from the cone

Fender Blues Deluxe 5 - pre+cab condendser mic off-axis 30cm off.json (176.0 KB)

Dynamic mic on-axis

Fender Blues Deluxe 6 - pre+cab dynamic mic on-axis.json (176.2 KB)

Dynamic mic off-axis

@TheRedOne

Then I took the pre-amp signal as an “input.wav” for the model, and the same respective mic’ed cabs as targets, to get the "cab only" models, to use two Aida-X plugins in the chain, one with the preamp model and the other with the “cab only” model loaded to imitate four-cable fx send/return setup, so I can put some pedals before the preamp, and some - in between the preamp and the power amp of the cabinet.

4-cable setup

@TheRedOne

Surprisingly it works, and if you A/B compare a “pre+cab” model and a “pre” model to a respective “cab only” model, well, at least I was not able to hear much difference in a blind test. Try it out yourself and let me know if it works for you.

A/B test setup

Here are the “cab only” models to be used with either the preamp model above or, I guess, any other “preamp only” model.

Condenser mic on-axis close up

Fender Blues Deluxe 2a - cab only condendser mic on-axis.json (175.5 KB)

Condenser mic off-axis close up

Fender Blues Deluxe 3a - cab only condendser mic off-axis.json (175.7 KB)

Condenser mic on-axis 30cm from the cone

Fender Blues Deluxe 4a - cab only condendser mic on-axis 30cm off.json (175.8 KB)

Condenser mic off-axis 30cm from the cone

Surprisingly, after like 20 or 30 attempts to train a model with a decent ESR (in my experience - anything less than 0,04), I just couldn’t make it. All the resulting models came out with ESR around 0,07 and were quite noisy. After a few sleepless nights I just gave up. Sorry, no model here!

Dynamic mic on-axis

Fender Blues Deluxe 6a - cab only dynamic mic on-axis.json (176.7 KB)

Dynamic mic off-axis

[gianfranco]

Gallien Krueger 700RB II Bass Amp Head by @jtemple0967

@jtemple0967

GK700RBii

• Contour and Presence at noon
• Treble at 11
• Hi-Mid at 11
• Low Mid at 1
• Bass at 2

Taken from the XLR direct out using “Post” EQ

GK700RBii.json (169.7 KB)

[gianfranco]

A couple of pedals by @Boukman

@Boukman

DemonFx TS9 K Clip.json (171.1 KB)
DRV 1981 Clone .json (170.6 KB)
Marshall Guvnor Plus.json (170.7 KB)
Strymon Deco G8.json (169.8 KB)
All the drive pedals are gain at half,except the Strymon which is a tape saturation with the gain at 3 o clock.
The DemonFx TS is at the TS9 setting with the clipping set to Keeley red dirt clipping.
The Guvnor plus has been modded to the original guvnor pedal.

[gianfranco]

Fender Twin Reberb (Vibrato Channel) and Fender Champ 5F1 Clone by @Boukman

@Boukman

Hi everyone!
I made a capture of my Fender Twin Reverb Vib channel (Silverface to Blackface conversion)
and my Champ 5F1 clone.
Hope you like them!
Champ G9.json (171.6 KB)
Fender Twin CH2.json (170.8 KB)

[gianfranco]

More pedals, by @Boukman

@Boukman

I made a few more pedal captures.Hope you like them!
They are all clones except the Bogner.
King of tone Clone Both.json (170.7 KB)
Protein CLone.json (170.5 KB)
Revv G3 g8.json (170.5 KB)
Supro Bold G9.json (170.7 KB)
Thorpy Peacekeeper.json (170.2 KB)
Bogner XTC High new.json (170.2 KB)
Bogner XTC Medium new.json (170.6 KB)
Colombo Plexi breed.json (170.9 KB)
Ethos TWE-1.json (170.4 KB)
JHS AT Clone 50w EP pre G6.json (170.7 KB)

[gianfranco]

Peavey VK100 HEAD HIGAIN Lead Channel by @ReedDunn

@ReedDunn

HI REED DUNN here with my First upload for MOD site!

ReedD VK100 personal setting.json (199.4 KB)

This is my second capture of my Vk100 this one is from my Neural Amp Modeler training NAM captures re trained for AIDA-X. More to Come.pretty heavy tone that i use on my amp.just past half for eq on sweet spots.and 3/4 for dampening and presence. lead channel with gain boost and volume boost.tube type dial is fully left for that extra power to the lead channel pre amp tubes. I hope you enjoy. only wish i have is for a noise gate in AIDA-X but i can easily use a fee one like GVST - GGate before AIDA-X works great.!!!KEEP IT LOUD!!!

[gianfranco]

Ceriatone King Kong - Part 3 (hotter) by @Boukman

@Boukman

Hi again!
I tried a few captures with hotter input signal.Let me know what you think
Ceriatone King Kong Channel 1 60s.json (170.3 KB)
KK new 60s br sw2 L .json (171.0 KB)
KK new 70s br sw2 L .json (170.9 KB)
KK new 80s br sw2 L .json (170.5 KB)

[gianfranco]

Ceriatone King Kong - Part 3 (boosted) by @Boukman

@Boukman

Hi!
I made a few more captures of my amp.I think they are getting better!I used some pedals in some captures to boost it.I`m really pleased with the sound!!
I think it sounds better than Line6 Helix already with the AIDA!!
Cheers!!

KK Ch2 Br sw both L feel dn 60s deep c bright R Lead 80s .json (170.5 KB)
KK Ch2 Br sw off feel dn 60s deep c bright r Guvnor boost - target.json (170.6 KB)
KK Ch2 Br sw both L feel dn 60s deep c bright R - target.json (170.5 KB)
KK CH2 Brsw both L feel dn 70s deep C bright R.json (170.9 KB)
KK Ch2 G1 Br sw L 70s deep c bright R Feel Up Hudson Broadcast.json (170.7 KB)

@Boukman

KK Ch1 Br sw L 60s deep c bright R boost SD.json (170.8 KB)
KK Ch2 G1 Br sw L 80s deep c bright R Feel Up.json (170.7 KB)
KK Ch2 G1 Br sw L 60s deep c bright R Feel Up DemonTS9 K.json (170.7 KB)
KK Ch1 Br sw L 60s deep c bright R Protein - .json (170.2 KB)
KK Ch1 Br sw L 60s deep c bright R Barber DD.json (170.7 KB)

[gianfranco]

Full “channel strip” for Electric Nylon Guitar by @Loris_Donatelli

@Loris_Donatelli

This is taken from the Logic settings, it’s my “channel strip” and is useful for a classical guitar sound, when the nylon string instrument has no microphone but only a piezo system. The reverb is already present, if someone wants it without I will do it again without so that you can choose the right reverb. Currently there is only EQ and COMP.
Electric Nylon Guitar.json (172.2 KB)

[gianfranco]

Victory Countess (The Jack) V4 Preamp by @Boukman

@Boukman

Here are some profiles of my tube preamp clean and drive channels at various gain settings.
Try using the power amp impulses plugin after.It works really nice!!
Victory Countess V4 Ch1 G 4 .json (171.2 KB)
Victory Countess V4 Ch2 G full.json (170.2 KB)
Victory Countess V4 Ch2 G 3q .json (170.5 KB)
Victory Countess V4 Ch2 Gain Half.json (170.6 KB)
Victory Countess V4 Ch2 Gain 1Q.json (170.8 KB)

@Boukman

Victory Countess V4 Ch1 G 9.json (170.8 KB)
Victory Countess V4 Ch1 G 6.json (170.9 KB)

@Boukman

I made this with lower gain…I think they sound clearer…
Victory V4 CH2 Gain 7.5 di 5 -11 lower esr.json (170.4 KB)
Victory V4 CH2 Gain 3 di 5 -11 - .json (170.5 KB)

[gianfranco]

Catalinbread DLS (Marshall Plexi Super Bass) by @novemberist

@novemberist

This is a model of my Catalinbread Dirty Little Secret pedal, which basically emulates the sound and character of a classic Marshall Plexi amp (set to “Super Bass” circuit in my case). I’ve chosen the lightest model for this one and have sampled 4 different degrees of the preamp knob (low,center,high,very high). No cab simulation of any kind included.

CB_DLS_Preamp_Low.json (15.7 KB)
CB_DLS_Preamp_Center.json (15.7 KB)
CB_DLS_Preamp_High.json (15.7 KB)
CB_DLS_Preamp_VeryHigh.json (15.7 KB)

[gianfranco]

AX84 P1 DIY Amp - Amp Only by @mreed707

@mreed707

Single 12AX7 and a single EL34 amp. Marshall sounding JTM ish. Set up as a pedal platform so just a little bit of break up. DI through Two Notes Captor into Logic. Guitar used, Fender Mustang with humbuckers so pushing the front a bit more than a single coil.
Clean AX84 P1.json (81.4 KB)